Shear characteristics of hydrated needle-punched GCL+GM composite liners at different temperatures
HAN Zhuo-wei1,2, LIN Hai1,2, SHI Jian-yong3
1. School of Civil Engineering and Architecture, Nanchang University, Nanchang 330031, China; 2. Key Laboratory of Tailings Reservoir Engineering Safety of Jiangxi Province, Nanchang University, Nanchang 330031, China; 3. Key Laboratory of Geomechanics and Embankment Engineering of the Ministry of Education, Hohai University, Nanjing 210098, China
Abstract:The composite liner consisting of needle-punched GCL and textured geomembrane (GM) is widely used, and changing temperature environment can be encountered when it is used to deal with mining-smelting waste or municipal solid waste. Aiming at the temperature effect of the shear strength of the composite liner, the large-scale temperature-controlled water-bath direct shear apparatus is used to carry out the whole shear tests without pre-determined failure surface for the hydrated needle-punched GCL+GM composite liner at different temperatures. The shear strengths of the composite liner in the range of 10℃~70℃ are obtained, and the shear characteristics of the composite liner under different temperatures as well as normal stress are revealed. The test results show that obvious peak strengths and obvious post-peak softening phenomena occur at the stress-displacement curve at all the test temperatures. The peak shear strength and large-displacement shear resistance of the composite liner achieve the maximum value at the room temperature of about 20℃, and either increasing or decreasing temperature can cause obvious reduction in the shear strength of the composite liner. The change of temperature has a significant effect on the shear strength and failure modes of the composite liner, and accordingly attention should be paid to the temperature effect on the stability of slopes containing geosynthetics.
韩卓韦, 林海, 施建勇. 不同温度下水化针刺GCL+GM复合衬里的剪切特性[J]. 岩土工程学报, 2021, 43(5): 962-967.
HAN Zhuo-wei, LIN Hai, SHI Jian-yong. Shear characteristics of hydrated needle-punched GCL+GM composite liners at different temperatures. Chinese J. Geot. Eng., 2021, 43(5): 962-967.
[1] 钱学德, 施建勇, 刘晓东. 现代卫生填埋场的设计与施工[M]. 北京: 中国建筑工业出版社, 2011 (QIAN Xue-de, SHI Jian-yong, LIU Xiao-dong.Design and Construction of Modern Sanitary Landfills[M]. Beijing: China Architecture and Building Press, 2011. (in Chinese)) [2] FOX P J, SURA J M, NYE C J.Dynamic shear strength of a needle-punched GCL for monotonic loading[J]. Journal of Geotechnical and Geoenvironmental Engineering, 2015, 141(7): 04015025. [3] TOUZE-FOLTZ N, BANNOUR H, BARRAL C, et al.A review of the performance of geosynthetics for environmental protection[J]. Geotextiles and Geomembranes, 2016, 44: 656-672 [4] FOX P J, STARK T D.State-of-the-art report: GCL shear strength and its measurement ten-year update[J]. Geosynthetics International, 2015, 22(1): 3-47. [5] 张宏伟, 林伟岸, 詹良通, 等. 土工膜/GCL 界面剪切强度特性的试验研究[J]. 土木工程学报, 2013, 46(2): 123-130. (ZHANG Hong-wei, LIN Wei-an, ZHAN Liang-tong, et al.Experiment study on shear strength of GM/GCL interface[J]. China Civil Engineering Journal, 2013, 46(2): 123-130. (in Chinese)) [6] 林海, 章玲玲, 刘小文, 等. 水化针刺GCL+GM复合衬里的单剪破坏特征[J]. 岩土工程学报, 2016, 38(9): 1660-1667. (LIN Hai, ZHANG Ling-ling, RUAN Xiao-bo, et al.Simple-shear failure characteristics of hydrated needle- punched GCL+GM composite liner[J]. Chinese Journal of Geotechnical Engineering, 2016, 38(9): 1660-1667. (in Chinese)) [7] 林海, 施建勇, 钱学德. 水化针刺GCL 剪切破坏机理的试验研究[J]. 岩土工程学报, 2017, 39(8): 1374-1380. (LIN Hai, SHI Jian-yong, QIAN Xue-de.Experimental research on shear failure mechanism of hydrated needle-punched GCLs[J]. Chinese Journal of Geotechnical Engineering, 2017, 39(8): 1374-1380. (in Chinese)) [8] YESILLER N, HANSON, J L, YEE E H.Waste heat generation: a comprehensive review[J]. Waste Management, 2015, 42(5): 116-179. [9] NAVID H Jafaria, TIMOTHY D Stark, TODD Thalhamerc.Spatial and temporal characteristics of elevated temperatures in municipal solid waste landfills[J]. Waste Management, 2017, 59(1): 286-301. [10] KOERNER G R, KOERNER R M.Long-term temperature monitoring of geomembranes at dry and wet landfills[J]. Geotextiles and Geomembranes, 2006, 24(2): 72-77. [11] HANSON J L, CHRYSOVERGIS T S, YESILLER N, et al.Temperature and moisture effects on GCL and textured geomembrane interface shear strength[J]. Geosynthetics International, 2015, 22(1): 110-124. [12] STARK T D, MARTIN J W, GERBASI G T, et al.Aluminum waste reaction indicators in a municipal solid waste landfill[J]. Geotechnical and Geoenvironmental Engineering, 2012, 138(3): 252-261. [13] LISTYARINI S.Designing heap leaching for nickel production that environmentally and economically sustain[J]. International Journal of Environmental Science and Development, 2017, 8(12): 799-803. [14] AKPINAR M V, BENSON C H.Effect of temperature on shear strength of two geomembrane-geotextile interfaces[J]. Geotextiles and Geomembranes, 2005, 23: 443-453. [15] GHAZIZADEH S, BAREITHER C A.Stress-controlled direct shear testing of geosynthetic clay liners II: assessment of shear behavior[J]. Geotextiles and Geomembranes, 2018, 46(5): 667-677. [16] GHAZIZADEH S, BAREITHER C A. Temperature effects on the peak and large-displacement shear strength of needle-punched reinforced GCLs[C]// Geosynthetics2019, 2019, At Houston. [17] GHAZIZADEH S, BAREITHER C A.Temperature- Dependent shear behavior of geosynthetic clay liners[J]. Geotechnical Frontiers, 2017, 280(3): 288-298. [18] BAREITHER C A, SOLEIMANIAN M, GHAZIZADEH S.Direct shear testing of GCLs at elevated temperature and in a non-standard solution[J]. Geosynthetics International, 2018, 25(3): 350-368.