Spatial block identification method based on meshing and its engineering application
ZHANG Min-si1, 3, HUANG Run-qiu2, WANG Shu-hong4, YANG Yong1, 3
1. Fundamental Science on Radioactive Geology and Exploration Technology Laboratory, East China Institute of Technology, Nanchang, 330013, China; 2. State Key Laboratory of Geohazard Prevention and Geoenvironment Protection, Chengdu University of Technology, Chengdu 610059, China; 3. Faculty of Civil and Architectural Engineering, East China Institute of Technology, Nanchang 330013, China; 4. School of Resources & Civil Engineering, Northeastern University, Shenyang 110819, China
Abstract:In order to solve the issue of spatial block identification of finite structural planes under complex geometrical boundaries, the geometric modeling concept of sagittal planes is proposed and the meshing method is introduced to the block theory. Firstly, the rock mass is meshed into small independent elements. Then the structural planes are added orderly and the elements are cut after the contact judgment. Finally, the independent spatial blocks are formed when the mesh is removed and the elements are united. The cutting method of blocks with arbitrary configurations is given by planes. Based on the merger of directional edge, the merging method of the same direction and opposite surface is united aiming at block merging. The results show that it has good advantages for the dynamical appending of structural planes and the building of complex geometry model. Moreover, there is no limit to the form and number of block identification, and the programming progress is simple. The prosposed method is further illustrated with its application to tunnel engineering in Liaoning Province. All of the independent spatial blocks are identified, and then the information of the key blocks is obtained. Its effectiveness and superiority in complex block identification is demonstrated through the engineering practice. It may provide technical support for the safety production of rock mass engineering.
张敏思, 黄润秋, 王述红, 杨勇. 基于网格划分的全空间块体识别方法及其工程应用[J]. 岩土工程学报, 2016, 38(3): 477-485.
ZHANG Min-si, HUANG Run-qiu, WANG Shu-hong, YANG Yong. Spatial block identification method based on meshing and its engineering application. Chinese J. Geot. Eng., 2016, 38(3): 477-485.
[1] SHI G H, GOODMAN R E. Two-dimensional discontinuous deformation analysis[J]. International Journal for Numerical and Analytical Methods in Geomechanics, 1985, 9: 541-556. [2] GOODMAN R E, SHI G H. Block theory and its application to rock engineering[M]. Englewood Cliff: Prentice Hall, 1985. [3] BOYLE W J, GOODMAN R E, YOW J L. Field cases using key block theory[C]// Proceedings of the International Symposium on Large Rock Caverns. Helsinki, 1986: 88-95. [4] IKEGAWA Y, HUDSON J A. A novel automatic identification system for three-dimensional multi-block systems[J]. Engineering Computations, 1992, 9(2): 169-179. [5] 汪卫明, 陈胜宏. 三维岩石块体系统的自动识别方法[J]. 武汉水利电力大学学报, 1998, 31(50): 51-55. (WANG Wei-ming, CHEN Sheng-hong. Automatic identification method for three-dimensional rock block systems[J]. Journal of Wuhan University of Hydraulic and Electric Engineering, 1998, 31(50): 51-55. (in Chinese)) [6] 卢 波, 陈剑平, 王良奎. 基于三维网络模拟基础的复杂有限块体的自动搜索及其空间几何形态的判定[J]. 岩石力学与工程学报, 2002, 21(8): 1232-1238. (LU Bo, CHEN Jian-ping, WANG Liang-kui. Automatic seeking for complex finite rock block and judgment of its spatial geometrical shape based on 3D network modeling[J]. Chinese Journal of Rock Mechanics and Engineering, 2002, 21(8): 1232-1238. (in Chinese)) [7] 邬爱清, 张奇华. 岩石块体理论中三维随机块体几何搜索[J]. 水利学报, 2005, 36(4): 426-432. (WU Ai-qing, ZHANG Qi-hua. Geometric identification of stochastic block in block theory[J]. Journal of Hydraulic Engineering, 2005, 36(4): 426-432. (in Chinese)) [8] 张奇华. 基于块体加与块体减算法的岩石块体几何形态分析[J]. 水利学报, 2006, 37(4): 418-424. (ZHANG Qi-hua. Morphological analysis of rock blocks by block adding subtracting method[J]. Journal of Hydraulic Engineering, 2006, 37(4): 418-424. (in Chinese)) [9] 钟登华, 鲁文妍, 刘 杰, 等. 基于三维地质模型的地下洞室曲面块体分析[J]. 岩石力学与工程学报, 2011, 30(增刊2): 3696-3702. (ZHONG Deng-hua, LU Wen-yan, LIU Jie, et al. Surface-block analysis of underground cavern based on 3D geological modeling[J]. Chinese Journal of Rock Mechanics and Engineering, 2011, 30(S2): 3696-3702. (in Chinese)) [10] 于青春, 薛果夫, 陈德基. 裂隙岩体一般块体理论[M]. 北京: 中国水利水电出版社, 2007. (YU Qing-chun, XUE Guo-fu, CHEN De-ji. General block theory for fractured rock mass[M]. Beijing: China Water Power Press, 2007. (in Chinese)) [11] WU J, ZHANG Z X, KWOK C Y. Stability analysis of rock blocks around a cross-harbor tunnel using the improved morphological visualization method[J]. Engineering Geology, 2015, 187: 10-31. [12] ZHANG Z X, LEI Q H. Object-oriented modeling for three-dimensional multi-block systems[J]. Computers and Geotechnics, 2013, 48: 208-227. [13] 王述红, 杨勇, 王 洋, 等. 基于数字摄像测量的开挖空间模型及不稳块体的快速识别[J]. 岩石力学与工程学报, 2010, 29(增刊1): 3432-3438. (WANG Shu-hong, YANG Yong, WANG Yang, et al. Spatial modeling and quick identification of unstable rock blocks based on digital photogrammetry[J]. Chinese Journal of Rock Mechanics and Engineering, 2010, 29(S1): 3432-3438. (in Chinese)) [14] WANG Shu-hong, HUANG Run-qiu, NI Peng-peng, et al. Fracture behavior of intact rock using acoustic emission: experimental observation and realistic modeling[J]. Geotechnical Testing Journal, 2013, 36(6): 903-914. [15] WANG Shu-hong, NI Peng-peng, GUO Mu-dan. Spatial characterization of joint planes and stability analysis of tunnel blocks[J]. Tunnelling and Underground Space Technology, 2013, 38: 357-367